~/tools/

Stair Calculator

Units
Precision

Straight stair

Total rise is finished floor to finished floor. The riser count comes from the ideal rise; pick another from the list if the run or headroom needs it.

Top tread
Possible rises
Run from

Construction

Built from
11 1/4" for a 2x12
Upper floor, joists included

Headroom

From the top riser back along the floor above

Balusters

Per tread

Rise and run

Risers
14 × 7 11/16"
Treadsfloor is the top landing
13 × 10"
Total run
10' 10"
Stair angle
37.65°
2R + T24 to 25 is comfortable
25 7/16"
Stringer lengthon the nosing line; add for the top and bottom cuts
14' 1"
Step along stringernosing to nosing
1' 5/8"
Stringer left below notch
5 1/8"
Bottom dropcut off the bottom so the first rise matches once treads are on
1"
Headroom at the opening80 in needs an opening 9' 8 11/16" long
6' 10 9/16"

2R + T is 25.4 in; 24 to 25 in is the comfortable range

Geometric only. Stair codes set the limits on rise, run, headroom, width and guard heights; check yours before building.

Flight

Straight stair

Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.

12345678910111213headroom 6' 10 9/16"opening 10' 0"total run 10' 10"total rise 9' 0"10"7 11/16"37.6°

Violet dashed line is the nosing line. Headroom is measured plumb from the nosing line to the underside of the floor at the opening edge; move the slider to see it change.

Tread heights

#MarkPosition
1Tread 17 11/16"
2Tread 21' 3 7/16"
3Tread 31' 11 1/8"
4Tread 42' 6 7/8"
5Tread 5 · landing possible3' 2 9/16"
6Tread 6 · landing possible3' 10 5/16"
7Tread 7 · landing possible4' 6"
8Tread 8 · landing possible5' 1 11/16"
9Tread 9 · landing possible5' 9 7/16"
10Tread 106' 5 1/8"
11Tread 117' 7/8"
12Tread 127' 8 9/16"
13Tread 138' 4 5/16"

Stringer running points

#MarkPosition
1Bottom0"
2Nosing 11' 5/8"
3Nosing 22' 1 1/4"
4Nosing 33' 1 7/8"
5Nosing 44' 2 1/2"
6Nosing 55' 3 1/8"
7Nosing 66' 3 3/4"
8Nosing 77' 4 7/16"
9Nosing 88' 5 1/16"
10Nosing 99' 5 11/16"
11Nosing 1010' 6 5/16"
12Nosing 1111' 6 15/16"
13Nosing 1212' 7 9/16"
14Nosing 1313' 8 3/16"

Tread heights are from the lower floor to the top of each tread, each rounded on its own. Landings are flagged where at least 36" of rise remains above and below. Stringer points are along the edge from the bottom end, nosing to nosing.

Stringer notching template

Print at 100% and step it along the board, or set a framing square to 7 11/16" rise and 10" run. Drop the bottom by the tread thickness.

Stringer notching

Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.

run 10"rise 7 11/16"37.65°drop 1"5 1/8" left

Balusters on the treads

2 per tread at 5" centres, first one 2 1/2" from the riser face; each is 3 7/8" longer than the one in front.

1232 1/2"5" c/crun 10"rise 7 11/16"

Lumber: nominal to actual

Enter actual finished sizes in every tool. A nominal 2x4 is cut and dressed to the size shown.

NominalActual
1x23/4" x 1 1/2"
1x33/4" x 2 1/2"
1x43/4" x 3 1/2"
1x63/4" x 5 1/2"
1x83/4" x 7 1/4"
1x103/4" x 9 1/4"
1x123/4" x 11 1/4"
2x21 1/2" x 1 1/2"
2x31 1/2" x 2 1/2"
2x41 1/2" x 3 1/2"
2x61 1/2" x 5 1/2"
2x81 1/2" x 7 1/4"
2x101 1/2" x 9 1/4"
2x121 1/2" x 11 1/4"
4x43 1/2" x 3 1/2"
4x63 1/2" x 5 1/2"
6x65 1/2" x 5 1/2"
The link carries every input, so it opens the same calculation on a phone.