~/tools/

Common Rafter Calculator

Units
Precision

Common rafter

Run is measured level from the ridge plumb cut to the outer face of the wall. Use the span box below to get it from the building width.

Slope as
Level, from the outer wall face to the tail plumb cut
Rafter
Actual
Actual
Birdsmouth by
Bearing on the plate, usually the wall thickness
Drawing only

Lengths and cuts

Roof angle6:12 pitch
26.57°
Riseover the run, on the measuring line
6' 0"
Line lengthridge plumb cut to the outer wall plumb line, along the rafter
13' 5"
Tail lengthouter wall to the tail cut, along the rafter
2' 2 13/16"
Overall lengthlong point to long point before any ridge shortening
15' 7 13/16"
Plumb cutsaw miter from square · length of the cut
26.57° · 8 1/8"
Seat cutfrom square · bearing on the plate
63.43° · 3 1/2"
Heel (birdsmouth plumb)
1 3/4"
Height above platetop of rafter over the outer wall face
6 3/8"
Birdsmouth depthsquare to the edge; 5 11/16" left
1 9/16"
Ridge above platetop of rafter at the ridge over the top of the wall
6' 6 3/8"
Tail top below plate
5 5/8"
Fascia bottom below plate
1' 1 3/4"

Lengths are to the ridge plumb cut on the centre line. Shorten the ridge end by half the ridge thickness measured level (13/16" along the rafter for a 1 1/2" ridge).

Rafter

Common rafter

Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.

run 12' 0"rise 6' 0"overhang 2' 0"line length 13' 5"tail 2' 2 13/16"HAP 6 3/8"26.57°ridge

Birdsmouth template

Print at 100% and lay the rafter's bottom edge along the drawing to mark the seat and heel. The dashed lines are the top and outer face of the wall plate.

Birdsmouth

Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.

26.6°heel 1 3/4"seat 3 1/2"HAP 6 3/8"

Ridge plumb cut template

The same angle marks the tail plumb cut. Set the saw miter to 26.57° from square.

Ridge plumb cut

Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.

plumb cut 8 1/8"26.57° from square

Run from the building width

Half the width between the outer wall faces, less half the ridge thickness.

Outside of wall to outside of wall
Run 12' 0"
building 24' 1 1/2"run 12' 0"run 12' 0"

Lumber: nominal to actual

Enter actual finished sizes in every tool. A nominal 2x4 is cut and dressed to the size shown.

NominalActual
1x23/4" x 1 1/2"
1x33/4" x 2 1/2"
1x43/4" x 3 1/2"
1x63/4" x 5 1/2"
1x83/4" x 7 1/4"
1x103/4" x 9 1/4"
1x123/4" x 11 1/4"
2x21 1/2" x 1 1/2"
2x31 1/2" x 2 1/2"
2x41 1/2" x 3 1/2"
2x61 1/2" x 5 1/2"
2x81 1/2" x 7 1/4"
2x101 1/2" x 9 1/4"
2x121 1/2" x 11 1/4"
4x43 1/2" x 3 1/2"
4x63 1/2" x 5 1/2"
6x65 1/2" x 5 1/2"
The link carries every input, so it opens the same calculation on a phone.