Gable studs
Stud lengths under a raked top plate. Use the full gable for a gable end framed as one wall, or the half gable for a single slope such as a shed or lean-to. Level studs are in the wall framing calculator.
Lengths and cuts
- Rake angle6:12 pitch
- 26.57°
- Studs2x4 at 16" centers
- 19
- Common differenceeach stud is this much longer than the last
- 8"
- Top cutsaw miter from square · 3/4" drop across the stud
- 26.57°
- Height at the ridgeincluding plates
- 14' 0"
- Riseover half the width
- 6' 0"
- Raked plateboth slopes together
- 26' 10"
- Plate plumb thicknessa raked plate takes this much stud height
- 1 11/16"
- Total stud length88.2 board feet
- 201' 7 1/8"
The ridge falls inside a stud; that stud is cut to a point with the top cut on both faces
| # | Center | Long point | Short point |
|---|---|---|---|
| 1 | 3/4" | 7' 9 9/16" | 7' 8 13/16" |
| 2 | 1' 4" | 8' 5 3/16" | 8' 4 7/16" |
| 3 | 2' 8" | 9' 1 3/16" | 9' 7/16" |
| 4 | 4' 0" | 9' 9 3/16" | 9' 8 7/16" |
| 5 | 5' 4" | 10' 5 3/16" | 10' 4 7/16" |
| 6 | 6' 8" | 11' 1 3/16" | 11' 7/16" |
| 7 | 8' 0" | 11' 9 3/16" | 11' 8 7/16" |
| 8 | 9' 4" | 12' 5 3/16" | 12' 4 7/16" |
| 9 | 10' 8" | 13' 1 3/16" | 13' 7/16" |
| 10 | 12' 0" | 13' 8 13/16" | 13' 8 7/16" both sides |
| 11 | 13' 4" | 13' 1 3/16" | 13' 7/16" |
| 12 | 14' 8" | 12' 5 3/16" | 12' 4 7/16" |
| 13 | 16' 0" | 11' 9 3/16" | 11' 8 7/16" |
| 14 | 17' 4" | 11' 1 3/16" | 11' 7/16" |
| 15 | 18' 8" | 10' 5 3/16" | 10' 4 7/16" |
| 16 | 20' 0" | 9' 9 3/16" | 9' 8 7/16" |
| 17 | 21' 4" | 9' 1 3/16" | 9' 7/16" |
| 18 | 22' 8" | 8' 5 3/16" | 8' 4 7/16" |
| 19 | 23' 11 1/4" | 7' 9 9/16" | 7' 8 13/16" |
Gable end
Gable end studs
Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.
| # | Mark | Position |
|---|---|---|
| 1 | end | 0" |
| 2 | 1' 3 1/4" | |
| 3 | 2' 7 1/4" | |
| 4 | 3' 11 1/4" | |
| 5 | 5' 3 1/4" | |
| 6 | 6' 7 1/4" | |
| 7 | 7' 11 1/4" | |
| 8 | 9' 3 1/4" | |
| 9 | 10' 7 1/4" | |
| 10 | 11' 11 1/4" | |
| 11 | 13' 3 1/4" | |
| 12 | 14' 7 1/4" | |
| 13 | 15' 11 1/4" | |
| 14 | 17' 3 1/4" | |
| 15 | 18' 7 1/4" | |
| 16 | 19' 11 1/4" | |
| 17 | 21' 3 1/4" | |
| 18 | 22' 7 1/4" | |
| 19 | end | 23' 10 1/2" |
| # | Mark | Position |
|---|---|---|
| 1 | end | 0" |
| 2 | 1' 5 1/16" | |
| 3 | 2' 10 15/16" | |
| 4 | 4' 4 13/16" | |
| 5 | 5' 10 11/16" | |
| 6 | 7' 4 5/8" | |
| 7 | 8' 10 1/2" | |
| 8 | 10' 4 3/8" | |
| 9 | 11' 10 1/4" | |
| 10 | 13' 4 3/16" | |
| 11 | 14' 10 1/16" | |
| 12 | 16' 3 15/16" | |
| 13 | 17' 9 13/16" | |
| 14 | 19' 3 11/16" | |
| 15 | 20' 9 5/8" | |
| 16 | 22' 3 1/2" | |
| 17 | 23' 9 3/8" | |
| 18 | 25' 3 1/4" | |
| 19 | end | 26' 8 5/16" |
Top cut template
Print at 100% and lay a stud edge along the left side to mark the cut. Set the saw miter to 26.57° from square; the cut drops 3/4" across the stud.
Gable stud top cut
Printing uses the real sizes. Set the printer scale to 100% and check one dimension with a tape before cutting.
Lumber: nominal to actual
Enter actual finished sizes in every tool. A nominal 2x4 is cut and dressed to the size shown.
| Nominal | Actual |
|---|---|
| 1x2 | 3/4" x 1 1/2" |
| 1x3 | 3/4" x 2 1/2" |
| 1x4 | 3/4" x 3 1/2" |
| 1x6 | 3/4" x 5 1/2" |
| 1x8 | 3/4" x 7 1/4" |
| 1x10 | 3/4" x 9 1/4" |
| 1x12 | 3/4" x 11 1/4" |
| 2x2 | 1 1/2" x 1 1/2" |
| 2x3 | 1 1/2" x 2 1/2" |
| 2x4 | 1 1/2" x 3 1/2" |
| 2x6 | 1 1/2" x 5 1/2" |
| 2x8 | 1 1/2" x 7 1/4" |
| 2x10 | 1 1/2" x 9 1/4" |
| 2x12 | 1 1/2" x 11 1/4" |
| 4x4 | 3 1/2" x 3 1/2" |
| 4x6 | 3 1/2" x 5 1/2" |
| 6x6 | 5 1/2" x 5 1/2" |